加好友 
发短信
Post By：2017-9-22 22:02:00 [只看该作者]
尝试重新下载内核，VS软件貌似也能进去调试，以下是串口打印的信息：
Microsoft Windows CE Bootloader Common Library Version 1.4 Built Jan 6 2015 10:34:27
Microsoft Windows CE Ethernet Bootloader 1.0 for MX25 3DS (Jan 6 2015 10:38:03)
INFO: Bootloader launched from NAND
FMD_Init::0
FMD_Init::NumberOfChip=1
INFO: OEMPlatformInit: Initialized NAND flash device.
->EM9170_IOConfig
->EM9170_ISABusSetup
INFO: Loading boot configuration from NAND
-> Eboot Splash Screen
-> Display_GetScreenConf
->FindBMP
EBOOT_ReadFlash: Reading 2048 bytes from NAND...
NandFlashChip: wDataBytesPerSector = 0x800 bytes, wSectorsPerBlock = 0x40
EBOOT_ReadFlash: reading completed successfully.
->FindBMP::800x600, bfOffBits=1066, bfSize=481068
EBOOT_ReadFlash: Reading 481068 bytes from NAND...
NandFlashChip: wDataBytesPerSector = 0x800 bytes, wSectorsPerBlock = 0x40
EBOOT_ReadFlash: reading completed successfully.
Display Format = 800*600
-> Display_Init
LCDC6xhw::LCDRefClk = 66500000
-> Display_Show
-> Display_On
System ready!
Preparing for download...
Press [ENTER] to launch image stored in NAND flash or [SPACE] to cancel.
Initiating image launch in 0 seconds.
Launching flash image ...
-BLMenu .
INFO: Using device name: 'MX2533'
INFO: Reading NK image from NAND (please wait)...
INFO: BinFS -> find MBR...
INFO: use RAM buffer at 0x83FF8000 as MBR buffer
INFO: Find MBR start from NAND flash sector [0x400].
INFO: MBR is at NAND flash block [0x10].
INFO: Partition 0, File system 0x23, StartSector 0x100, TotalSectors 0xA80.
INFO: StartLogBlkAddr=0x14, EndLogBlkAddr=0x3D
INFO: dwNkRamStart=0xA0200000, dwImageStart=0x91580000
##########################################
INFO: Loading of NK completed successfully.
OEMLaunch::use BootCFG -> dwImageStart = 0x91580000, dwLaunchAddr = 0x80200000, dwImageLength = 0x2C0000
Download successful! Jumping to image at 0x80200000 (physical 0x80200000)...
EbootWDOG_EnቱRO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
BSP Clock Configuration:
MCU PLL = 532000000 Hz
USB PLL = 240000000 Hz
ARM CLOCK = 399000000 Hz
AHB CLOCK = 133000000 Hz
IPG CLOCK = 66500000 Hz
USB CLOCK = 60000000 Hz
Periph Clk CSI = 66500000 Hz
Periph Clk EPIT = 66500000 Hz
Periph Clk ESAI = 66500000 Hz
Periph Clk ESDHC1 = 66500000 Hz
Periph Clk ESDHC2 = 66500000 Hz
Periph Clk GPT = 66500000 Hz
Periph Clk I2C = 66500000 Hz
Periph Clk LCDC = 66500000 Hz
Periph Clk NFC = 33250000 Hz
Periph Clk OWIRE = 66500000 Hz
Periph Clk PWM = 66500000 Hz
Periph Clk SIM1 = 66500000 Hz
Periph Clk SIM2 = 66500000 Hz
Periph Clk SSI1 = 66500000 Hz
Periph Clk SSI2 = 66500000 Hz
Periph Clk UART = 66500000 Hz
Windows CE Kernel for ARM (Thumb Enabled) Built on Nov 3 2010 at 07:30:04
INFO:OALLogSetZones: dpCurSetХͭzUU֮er On Reset
OEMInit: silicon rev = 0x2
+OALInitRTC
OALInitRTC::Setup GPIO based I2C interface for ISL1208
dry ice initial status 0x103
dry ice status 0x3
RTC not running. turning it on now
-OEMInit
OALIoCtlHalPostInit::InitializeCriticalSection(&g_oalNfcMutex)
+RefreshWatchdogTimer: First call, init the Wdog to timeout reset in 10 secs
-->WdogInit: Watchdog
ISL1208SetRealTime: OK 2006-1-1
OALIoCtlHalInitRTC(2006-1-1 12:0:0)
FMD_Init::0
FMD_Init::NumberOfChip=1
NANDDisk: d_StartBlock = 0x10, d_TotalSize = 0x23c0000 bytes.
Flash PDD: Init()
FlashPdd_Init: m_dwRegionNumber = 1.
<-Flash PDD: Init() OK
GpioAlloc passed!
IomuxAlloc passed!
ClockAlloc passed!
I2C_Init +
I2C_Init - hDev=0xd04f82a0
->ADC_Init
<-ADC_Init 0xd04f88e0
ISA_Init +
ISA_Init - hDev=0xd04f9540
->RNGB_GetRandomData
FEC: +DriverEntry(0xD04FC460, 0xD04FC470)
FEC: -DriverEntry [0x00000000]
FEC: +FECInitialize
BSPFECMacAddress: d0-9b-05-00-00-21
FEC: +FECEnetInit
CS&ZHL::BSPFECIomuxConfig 1
BSPPhyEnable::EM9170
BSPPhyReset:: Reset DM9161A
FEC: +FECParseDM9161State
FEC: 10Mbps Full Duplex
FEC: 10Mbps Half Duplex
FEC: 100Mbps Full Duplex
FEC: 100Mbps Half Duplex
BKL_INIT() +!
BKL_INIT() -!
SPI_Init +
--->CspiInitialize
CspiInitialize: DMA enabled (Base: 0x50004000)
CspiInitialize: DMA enabled (Base: 0x50004000)
SPI_Init: CSPI index = 3, pCspi=0xd08f0a00
SerInit+
SerInit - Initialization OK
SerInit+
SerInit - Initialization OK
SerInit+
SerInit - Initialization OK
SerInit+
SerInit - Initialization OK
ExSerInit::quit COM6 driver installation.
ExSerInit::quit COM7 driver installation.
ExSerInit::quit COM8 driver installation.
ExSerInit::quit COM9 driver installation.
->CAN_Init::flexcan driver
<-CAN_Init - hDev=0xd08f74e0
->CAN_Init::flexcan driver
<-CAN_Init - hDev=0xd08f66a0
WDT_Init +
InitializeHost2Mux::USBH2_OC <- pin-PWM in EM9170
ConfigUSBH2::polarity of USBH2 overcurrent is HIGH active
ConfigUSBH2::The USBPWR and OC pins are not used by USBH2
USB HardwareInitialize -> 0xd0bd0000
BspESDHCInit::config SD1 pins.
Config XVC as Dev
->IRQ_Init
<-IRQ_Init:: IrqNo=69, SysIntr=30
->IRQ_Init
IRQ_Init::failed to read TrueInstall.
->BSPInitLCDC
BSPInitLCDC:: PanelTyepe5 -> 800*600
GetVMemSizeFromRegistry: succeeds, size is 9437184!
LayMgr.cpp: Layout Manager successfully initialized to 1
+Touch screen Init
Maximum Allowed Error 16:
Install NandFlash2...
Flash PDD: Init()
FlashPdd_Init: m_dwRegionNumber = 2.
<-Flash PDD: Init() OK
ActivateDevice success.
EM9170 Emtronix Built at Jan 6 2015 10:38:05
Adaptation performed by Emtronix (c)
AdapterName: FEC1
EM9170 Debug Mode
Explorer(V2.0) taskbar thread started.
NDISPWR:: Found adapter [FEC1]
AUTORAS:: Dialer notifies: [1] [Dialer Start]
Posting WM_NETCONNECT(TRUE) message
AUTORAS:: Dialer notifies: [4] [Dialer Connected]
GetUserInfoFile: no qualified userinfo.txt in flash!
SetMemoryDivision : invalid StorePercent
\USBDisk\autotest.txt file isnot exist!
IOCTL_HAL_WSTARTUP_END: wstartup is ended!
