客人
Post By：2015-3-3 13:25:00 [只看该作者]
我用的是9281的板子，通过USB 连接到我的电脑后，提示： 无法识别的USB设备，不知为何？
后来打开了 Windows Mobile 设备中心，也是提示：未连接
后来用 串口调试助手，连接DEBUG COM 口之后，上传的信息如下： 不知怎么办
HTLLC00000000
BATT:3.90V
B
OFF 5VP.
WDT
LLLCBSP Clock Configuration:
PLL0 = 480000000 Hz
PLL1 = 480000000 Hz
PLL2 = 0 Hz
REF_CPU = 480000000 Hz
REF_EMI = 392727272 Hz
REF_IO0 = 480000000 Hz
REF_IO1 = 480000000 Hz
REF_PIX = 480000000 Hz
REF_HSADC = 480000000 Hz
REF_GPMI = 480000000 Hz
REF_PLL = 480000000 Hz
REF_XTAL = 24000000 Hz
REF_ENET_PLL= 0 Hz
P_CLK = 240000000 Hz
H_CLK = 80000000 Hz
X_CLk = 24000000 Hz
ETM = 24000000 Hz
EMI = 196363636 Hz
SSP0 = 24000000 Hz
SSP1 = 24000000 Hz
SSP2 = 24000000 Hz
SSP3 = 24000000 Hz
GPMI = 24000000 Hz
HSADC = 26666666 Hz
LCDIF = 24000000 Hz
SPDIF = 120000000 Hz
UTMI0 = 480000000 Hz
UTMI1 = 480000000 Hz
UART24MHZ = 24000000 Hz
PWM24MHZ = 24000000 Hz
TIMROT32K = 32000 Hz
Microsoft Windows CE Bootloader Common Library Version 1.4 Built Feb 4 2015 09:39:13
Microsoft Windows CE Ethernet Bootloader 1.0 for MX28 (Feb 4 2015 09:43:40)
->FMD_Init
reset GPMI module
FMD_Init::NumberOfChip=1
NAND_ECCConfLayout, pagesize=2048,sparesize=64
->FMD_GetInfo
FMD_GetInfo::dwNumBlocks = 1024
FMD_GetInfo::wSectorsPerBlock = 64
FMD_GetInfo::wDataBytesPerSector = 2048
FMD_GetInfo::dwBytesPerBlock = 131072
<-FMD_GetInfo
<-FMD_Init 0x80041760
INFO: OEMPlatformInit: Initialized NAND flash device.
INFO: Loading boot configuration from NAND
System ready!
Preparing for download...
INFO: Initial Eboot Screen Display...
->FindBMP
NANDReadImage::Reading 2048 bytes started from NAND Block 0x17...
NANDReadImage: reading completed successfully.
NANDReadImage::Reading 2048 bytes started from NAND Block 0x11...
NANDReadImage: reading completed successfully.
FindBMP::panel info 480x272, freq=9.0 MHz
<-FindBMP::480x272, bfOffBits=938, bfSize=131500
NANDReadImage::Reading 131500 bytes started from NAND Block 0x11...
NANDReadImage: reading completed successfully.
->GenericTFT_Init
GenericTFT_Init: setup pixel clock 9000000 Hz
->GenericTFT_ConfigurePanel
<-GenericTFT_ConfigurePanel
<-GenericTFT_Init
ShowBmp: Generic TFT
Debug Mode -> disable WDT
Press [ENTER] to launch image stored in NAND flash or [SPACE] to cancel.
Press [ENTER] to launch image stored in NAND flash or [SPACE] to cancel.
Initiating image launch in 3 seconds. 2 seconds. 1 seconds. 0 seconds.
Launching flash image ...
-BLMenu .
INFO: Using device name: 'MX285116'
INFO: Reading NK image from NAND (please wait)...
INFO: search MBR...
INFO: Partition 0, File system 0x23, StartSector 0x40, TotalSectors 0xDC0.
Copy NK from NAND flash to RAM...
#######################################################
INFO: Loading of NK completed successfully.
OEMLaunch called PhysAddress 0x40200000.
Download successful! Jumping to image at 0x0 (physical 0x40200000)...
Always Enable WDT before Launch...
。。。。。。。
